Alpha alternator, small PIA, or major PIA?
|
Alpha alternator, small PIA, or major PIA?
|
Aug 11 2013, 08:54 PM
|
|
Resident Guitar Guru Group: Leader Posts: 3,734 Posts Per Day: 0.64 Thanks Received: 437 Trader Stats: 4 (100%) Joined: 28-May 08 From: South Lyon, MI Member No.: 6,125 Mood: Pensive |
The wife's Rio has been sitting for a couple of weeks because of her recovery from the c-section. I went to fire it up today so we could drive it and the battery was dead. No big deal, I have a charger. Threw the charger on there, tried to fire it up, didn't hardly turn over. Okay, looks like the battery is the original so I'll get around to replacing it. Threw the charger on again just in case, and got it to turn over and fire. Alternator belt starts squealing immediately, then started smoking. Shut the car off, looked for the source of the smoke, and also found bits of belt dust everywhere. I'm thinking perhaps the alternator has seized, so I'm going to have to replace it as well.
Just how big a PIA is this going to be? I'm thinking that I'm going to go ahead and do the timing belt and water pump while I'm in there, but just looking at it makes me think it's going to be a multi-day project. Has anyone done one on a Rio/Accent? This is an '03, if it helps you out. -------------------- |
|
|
Aug 11 2013, 09:56 PM
|
|
Outta the way! Group: Leader Posts: 5,972 Posts Per Day: 0.85 Thanks Received: 272 Trader Stats: 4 (100%) Joined: 27-January 05 From: Citrus Heights, CA Member No.: 33 Mood: Cocky |
The Elantra alternator replacement is pretty simple. I haven't done it myself, but I've read about members doing the job in pretty short order. If you're savvy enough to do the timing belt, the alternator should be a breeze.
-Roy -------------------- |
|
|
Aug 12 2013, 09:11 AM
|
|
Proud GLT Owner Group: Lifetimer Posts: 21,140 Posts Per Day: 3.02 Thanks Received: 633 Trader Stats: 3 (100%) Joined: 11-March 05 From: Brownsburg, IN Member No.: 532 Mood: Hyper |
03 is pre-Accent sharing, so I'm not sure. I believe it is on the same side as the alpha/beta/theta (down low passenger side.). If it's typical asian, it'll be 12mm retention bolts, 10mm for the power wire and it'll likely have to comeout the bottom.
-------------------- Founding Member of the Indiana Chapter of the Teeny Weeny Club for Secure Adult Males
"Drag racing is for fast cars, and autocrossing is for fast drivers" -Toecutter |
|
|
Aug 12 2013, 06:31 PM
|
|
Resident Guitar Guru Group: Leader Posts: 3,734 Posts Per Day: 0.64 Thanks Received: 437 Trader Stats: 4 (100%) Joined: 28-May 08 From: South Lyon, MI Member No.: 6,125 Mood: Pensive |
03 is pre-Accent sharing, so I'm not sure. I believe it is on the same side as the alpha/beta/theta (down low passenger side.). If it's typical asian, it'll be 12mm retention bolts, 10mm for the power wire and it'll likely have to comeout the bottom. Actually, it's not that low. It's accessible from the top, but because of the intake/air conditioning hoses I don't think it'll come out through the top. -------------------- |
|
|
Aug 15 2013, 11:40 AM
|
|
Resident Guitar Guru Group: Leader Posts: 3,734 Posts Per Day: 0.64 Thanks Received: 437 Trader Stats: 4 (100%) Joined: 28-May 08 From: South Lyon, MI Member No.: 6,125 Mood: Pensive |
So I'm elbow-deep in it now... doing the alternator, battery, timing belt and water pump. The car, as expected, is mounting terrific resistance to my efforts. Right now, my problem is trying to get the power steering pump loosened enough to remove that belt (it's the outer of the 2 anyway). The trick is the bolt labeled 7 in this picture:
It seems that the head of it is buried where I can't get at it, and the nut on the other side is restricted access due to the exhaust manifold. After lunch, I guess I'm going to try to locate the head of the bolt and give the air tools another go at it (or perhaps my breaker bar), but failing that, any suggestions? -------------------- |
|
|
Aug 15 2013, 11:52 AM
|
|
back to basics again Group: Lifetimer Posts: 3,622 Posts Per Day: 0.51 Thanks Received: 248 Trader Stats: 1 (100%) Joined: 27-January 05 From: Katy, Texas Member No.: 52 Mood: Happy |
Are you trying to get to the bolt from up top? Try coming at it from the wheel well if possible.
Looks like it is low like where the alternator is in the Elantra. Turn the wheel (or remove it) and move the splash shield in the wheel well and see if it is there. Not sure if it the same, but worth a try. -------------------- "Those who yell the loudest about how unfair the world treated them are usually the reason for the treatment in the first place". A nurse on a forum I am on |
|
|
Aug 15 2013, 12:05 PM
|
|
Resident Guitar Guru Group: Leader Posts: 3,734 Posts Per Day: 0.64 Thanks Received: 437 Trader Stats: 4 (100%) Joined: 28-May 08 From: South Lyon, MI Member No.: 6,125 Mood: Pensive |
Are you trying to get to the bolt from up top? Try coming at it from the wheel well if possible. Looks like it is low like where the alternator is in the Elantra. Turn the wheel (or remove it) and move the splash shield in the wheel well and see if it is there. Not sure if it the same, but worth a try. I think it's up too high to get at from the wheel well, but I'll take a look in a bit (read: after we get the kids down for a nap). I did take the wheel off, knowing that it's definitely going to be easier to get at the timing sprocket from that end. Stay tuned. -------------------- |
|
|
Aug 15 2013, 12:15 PM
|
|
Proud GLT Owner Group: Lifetimer Posts: 21,140 Posts Per Day: 3.02 Thanks Received: 633 Trader Stats: 3 (100%) Joined: 11-March 05 From: Brownsburg, IN Member No.: 532 Mood: Hyper |
You are replacing that belt as well right? Cut it. The new one you can get on by starting it by hand then turning hte pulley to seat it. If this is one of the pre-smart t-belt jobs, you'll have to support the engine and take the side mount off. When you do that, you can use the jack to raise and lower the engine to make certain bolts easier to get to.
-------------------- Founding Member of the Indiana Chapter of the Teeny Weeny Club for Secure Adult Males
"Drag racing is for fast cars, and autocrossing is for fast drivers" -Toecutter |
|
|
1 members thank Bobzilla for this post Vinnie | |
Aug 15 2013, 12:21 PM
|
|
Resident Guitar Guru Group: Leader Posts: 3,734 Posts Per Day: 0.64 Thanks Received: 437 Trader Stats: 4 (100%) Joined: 28-May 08 From: South Lyon, MI Member No.: 6,125 Mood: Pensive |
You are replacing that belt as well right? Cut it. The new one you can get on by starting it by hand then turning hte pulley to seat it. If this is one of the pre-smart t-belt jobs, you'll have to support the engine and take the side mount off. When you do that, you can use the jack to raise and lower the engine to make certain bolts easier to get to. That might not be a bad idea... provided I've got something burly enough to cut the belt. I'm hoping I can do it the "normal" way, though. -------------------- |
|
|
Aug 15 2013, 01:36 PM
|
|
Resident Guitar Guru Group: Leader Posts: 3,734 Posts Per Day: 0.64 Thanks Received: 437 Trader Stats: 4 (100%) Joined: 28-May 08 From: South Lyon, MI Member No.: 6,125 Mood: Pensive |
Power steering pump has been defeated. Turns out, the bolt is only accessible from the top, provided you have the pulley turned just right so you can access the bolt through one of the two holes in the pulley. Next up, alternator. Trying to figure out the best way to get at the bottom bolt and then remove/replace... looking like through the bottom. Ack.
-------------------- |
|
|
Aug 15 2013, 07:06 PM
|
|
Resident Guitar Guru Group: Leader Posts: 3,734 Posts Per Day: 0.64 Thanks Received: 437 Trader Stats: 4 (100%) Joined: 28-May 08 From: South Lyon, MI Member No.: 6,125 Mood: Pensive |
Well, now I've got a real snag... the head snapped off the alternator mounting bolt. I'm going to surf the mall and find some sort of screw extractor set and hope that that and a new can of PB'laster will save my bacon.
The good thing is that my wife isn't driving again yet after the c-section. The car can sit immobile for another month and a half, but I'm going to try really hard to have it back on the road by next weekend. -------------------- |
|
|
Aug 29 2013, 10:25 PM
|
|
Resident Guitar Guru Group: Leader Posts: 3,734 Posts Per Day: 0.64 Thanks Received: 437 Trader Stats: 4 (100%) Joined: 28-May 08 From: South Lyon, MI Member No.: 6,125 Mood: Pensive |
So I'll be headed back under the car tomorrow... hopefully to remove that freakin' bolt that busted off. Might have to bust out the 6" long drill bit so I can get a run at the bolt from the far side of the obstructions.
-------------------- |
|
|
Similar Topics
Topic | Replies | Topic Starter | Views | Last Action | |
---|---|---|---|---|---|
Alternator replacement cost? | 4 | Kristen523 | 802 | 9th November 2015 - 12:22 AM Last post by: cobas |
|
Alternator Change Should I cjhange alternator |
2 | Alfonz | 665 | 8th February 2013 - 09:55 AM Last post by: The Gegenator |
|
Alpha timing belt change Anyone here done one? |
6 | bhorste | 8,389 | 17th January 2013 - 03:38 PM Last post by: bhorste |
|
Alternator removal tips | 18 | sarge | 3,185 | 23rd October 2012 - 08:36 PM Last post by: Vinnie |
|
Alternator whine with XM unit. | 8 | Tom06 | 9,759 | 22nd October 2012 - 12:02 AM Last post by: cw_52 |
Copyright 2022 The Elantra Club   | Time is now: 4th May 2024 - 07:19 AM |
Elantra Club is not affiliated in any way with Hyundai Motor America |