This is an archived forum community. It's currently closed to new memberships.
ElantraClub - for all generations

Welcome Guest ( Log In | Register )

 Forum Rules Overview
2 Pages V   1 2 >  
Reply to this topicStart new topic
> Beta Head Work
2000J25SP
post Mar 9 2016, 09:59 PM
Post #1 | Print


Poster Pro
Group Icon
Group: Lifetimer
Posts: 844
Posts Per Day: 0.18
Thanks Received: 229
Trader Stats: 0 (0%)
Joined: 29-June 11
From: NC
Member No.: 10,610
Mood: Amused


A few weeks ago I noticed excessive oil consumption, about half of a quart every one hundred miles. As well as occasional black smoke coming from the exhaust. There's no visible oil leaks. So I assumed the one hundred and ninety thousand mile piston rings were starting to show their age. The compression test showed that all cylinders were between 210-215 psi. So one would assume that the rings are actually in decent condition. Now I believe the valve stem seals are worn. I figured if I were to install new valve stem seals, I would rather install them on the better flowing solid lifter Beta 2 non-cvvt cylinder head. So I acquired a 2002 Elantra head for fifty dollars.
And then I figured If I were to take the time to install another head, I may as well take a bit more time and install a decked Beta 2 head with head work.

I'm about six hours into this project and probably have another ten to go. I'll need to get an extension for the Dremel.
It will probably be a few weeks until I will be able to finish and install the head.







Here are the before and the halfway finished exhaust ports:



--------------------

2000 Elantra
Go to the top of the page
 
+Quote Post
slowgls
post Mar 9 2016, 10:27 PM
Post #2 | Print


That Guy..
Group Icon
Group: Leader
Posts: 6,687
Posts Per Day: 1.18
Thanks Received: 724
Trader Stats: 16 (100%)
Joined: 20-September 08
From: Neenah, WI
Member No.: 6,539
Mood: Thankful


Very nice. Should pick just some nice gains with the cams.


--------------------


"This may be true but it is a chrysler sebring which is synonomous with being a p.o.s. car. Personally I gotta say it's getting
really tiring having to clean off the sopping wet panties from my Hyundai Elantra every morning. Bitches love Hyundais."

"Sometimes you wonder how the sperm that made that idiot was the fastest swimmer. . . Must've had a "race motor" in it with nass under the hood. . . " - Alex2013gt
Go to the top of the page
 
+Quote Post
bhorste
post Mar 12 2016, 02:26 PM
Post #3 | Print


Resident Guitar Guru
Group Icon
Group: Leader
Posts: 3,734
Posts Per Day: 0.65
Thanks Received: 437
Trader Stats: 4 (100%)
Joined: 28-May 08
From: South Lyon, MI
Member No.: 6,125
Mood: Pensive


Looks nice. Want to come work on mine (with almost 230k on it)?


--------------------

-Ben
'03 GT, and a proud Lifetimer
'14 Ford Fiesta SE

http://www.lagerhaus5.com
Go to the top of the page
 
+Quote Post
2000J25SP
post May 2 2016, 08:30 PM
Post #4 | Print


Poster Pro
Group Icon
Group: Lifetimer
Posts: 844
Posts Per Day: 0.18
Thanks Received: 229
Trader Stats: 0 (0%)
Joined: 29-June 11
From: NC
Member No.: 10,610
Mood: Amused


Update: I'm only about half way done. A lot of my time has been going into my S10, which required much more work than I previously thought. I did change jobs a month ago, which gives me more free time.


LOL at my original post, I estimated 16 hours. It'll probably be closer to 40 when It's all said and done.

I had planned to use the two 240 duration Beta 1 exhaust cams in this head. But I've been thinking about using a Beta 2 cvvt intake camshaft on the intake side. It's 250 Duration but requires a bit more modification to fit than the Beta 1 Exhaust cam did to fit.



--------------------

2000 Elantra
Go to the top of the page
 
+Quote Post
bhorste
post May 3 2016, 08:21 PM
Post #5 | Print


Resident Guitar Guru
Group Icon
Group: Leader
Posts: 3,734
Posts Per Day: 0.65
Thanks Received: 437
Trader Stats: 4 (100%)
Joined: 28-May 08
From: South Lyon, MI
Member No.: 6,125
Mood: Pensive


I would love to have the means to just throw at a project like this... she may not be the loudest screamer on the block, but she'll have it where it counts.


--------------------

-Ben
'03 GT, and a proud Lifetimer
'14 Ford Fiesta SE

http://www.lagerhaus5.com
Go to the top of the page
 
+Quote Post
2000J25SP
post Jul 1 2016, 09:07 PM
Post #6 | Print


Poster Pro
Group Icon
Group: Lifetimer
Posts: 844
Posts Per Day: 0.18
Thanks Received: 229
Trader Stats: 0 (0%)
Joined: 29-June 11
From: NC
Member No.: 10,610
Mood: Amused


Well, It's almost done. It'll definitely be finished next week though.



--------------------

2000 Elantra
Go to the top of the page
 
+Quote Post
1 members thank J2/RD for this post
bhorste
2000J25SP
post Jul 9 2016, 06:36 PM
Post #7 | Print


Poster Pro
Group Icon
Group: Lifetimer
Posts: 844
Posts Per Day: 0.18
Thanks Received: 229
Trader Stats: 0 (0%)
Joined: 29-June 11
From: NC
Member No.: 10,610
Mood: Amused


Update:

The head is 98% done. The new gaskets, head bolts and other misc parts arrived. I went with an oem 2001+ two layer mls head gasket. I believe it's .010 thinner. So it'll be equal to decking the head .050 The compression should be at least 11.0:1

My friend gave me a set of 4G63T valve springs. They're a bit stiffer than the Beta 2 springs.


I was at Dyno Day today and figured I'd do a "before" dyno and go again next month with the new head.

Did two runs, it made 131WHP/129FTLB and 132WHP/129LBFT the second run.
Current performance mods: $36 Ebay intake and various junkyard parts.


--------------------

2000 Elantra
Go to the top of the page
 
+Quote Post
1 members thank J2/RD for this post
bhorste
2000J25SP
post Oct 11 2016, 05:44 PM
Post #8 | Print


Poster Pro
Group Icon
Group: Lifetimer
Posts: 844
Posts Per Day: 0.18
Thanks Received: 229
Trader Stats: 0 (0%)
Joined: 29-June 11
From: NC
Member No.: 10,610
Mood: Amused


Well this took a few months longer than I anticipated...

So the story goes: I bought the Beta 2 head, spent a long ass time working on it. Then found a microscopic crack between the valve seats.
Sent the head to a machinist. He pulled out two of the valve seats, welded the crack, pressed in new valve seats. Did a valve job and shimmed the lifters. It took a LONG time to get the head back. I decided to replace the bearings and piston rings while it was apart. Then I found an excellent deal on new OEM 1.8 liter pistons. $10 each...

Well I FINALLY put the car back together, and... I love driving it, if you have the means I highly recommend picking one up.

The 1.8 pistons alone take it from the stock 10.3:1 compression to 11.0:1, plus the head was decked 40 thousandths. So the compression is around 12.0:1 it seems to run fine on 93 octane. I also used the stiffer 4g63t valve springs.

The car DEFINITELY pulls harder. The next dyno day is in two weeks. I would be shocked if the gains are less than 10whp. I'm going to guess at least mid to high 140's.

It's not a lot of power but it helps if you compare the power to weight ratio to an Elantra XD.
132whp J2 (2300lbs) is equal to a 166whp XD (2900lbs)
145whp J2 (2300lbs) is equal to a 183whp XD (2900lbs)
Plus my car has much shorter gearing which helps a lot.

I set the SAFC to + 20% from 3500-5500 and + 15% from 6000-7000 for a base tune and then gradually lean it out from there. It actually ran low 13's (afr) until 6000, then mid 12's. So the engine definitely breathes better now. These engines seems happiest at mid to high 12's, so I will have to add more fuel below 6,000


--------------------

2000 Elantra
Go to the top of the page
 
+Quote Post
3 members thank J2/RD for this post
bhorste, roydjt, slowgls
2000J25SP
post Nov 5 2016, 04:11 PM
Post #9 | Print


Poster Pro
Group Icon
Group: Lifetimer
Posts: 844
Posts Per Day: 0.18
Thanks Received: 229
Trader Stats: 0 (0%)
Joined: 29-June 11
From: NC
Member No.: 10,610
Mood: Amused


136whp 136 ft lb... sad.gif


--------------------

2000 Elantra
Go to the top of the page
 
+Quote Post
1 members thank J2/RD for this post
slowgls
bhorste
post Nov 5 2016, 08:37 PM
Post #10 | Print


Resident Guitar Guru
Group Icon
Group: Leader
Posts: 3,734
Posts Per Day: 0.65
Thanks Received: 437
Trader Stats: 4 (100%)
Joined: 28-May 08
From: South Lyon, MI
Member No.: 6,125
Mood: Pensive


Not bad numbers. Just how open is the intake?


--------------------

-Ben
'03 GT, and a proud Lifetimer
'14 Ford Fiesta SE

http://www.lagerhaus5.com
Go to the top of the page
 
+Quote Post
2000J25SP
post Nov 6 2016, 09:00 AM
Post #11 | Print


Poster Pro
Group Icon
Group: Lifetimer
Posts: 844
Posts Per Day: 0.18
Thanks Received: 229
Trader Stats: 0 (0%)
Joined: 29-June 11
From: NC
Member No.: 10,610
Mood: Amused


Crappy numbers. The runs were done on a Dynojet in 3rd gear. So the numbers are rather optimistic.

+4hp That's a 3% increase in power. Terrible... The compression alone should add 3% or more.

The car ran 12.2-12.8 afr 4,000-6750 rpm. So it should be a better tune than the first dyno.
Ignition timing is between 25-28 at wot.

@ Bhorste the stock intake manifold is untouched. It's not the biggest restriction. So cutting it apart and porting it and welding it back together wouldn't be worth it.


--------------------

2000 Elantra
Go to the top of the page
 
+Quote Post
slowgls
post Nov 6 2016, 10:27 AM
Post #12 | Print


That Guy..
Group Icon
Group: Leader
Posts: 6,687
Posts Per Day: 1.18
Thanks Received: 724
Trader Stats: 16 (100%)
Joined: 20-September 08
From: Neenah, WI
Member No.: 6,539
Mood: Thankful


QUOTE (J2/RD @ Nov 5 2016, 03:11 PM) *
136whp 136 ft lb... sad.gif

Well I was hope you would get more, but not bad at the wheels. The intake could be coaking the flow at thus point.


--------------------


"This may be true but it is a chrysler sebring which is synonomous with being a p.o.s. car. Personally I gotta say it's getting
really tiring having to clean off the sopping wet panties from my Hyundai Elantra every morning. Bitches love Hyundais."

"Sometimes you wonder how the sperm that made that idiot was the fastest swimmer. . . Must've had a "race motor" in it with nass under the hood. . . " - Alex2013gt
Go to the top of the page
 
+Quote Post
2 Pages V   1 2 >
Reply to this topicStart new topic
3 user(s) are reading this topic (3 guests and 0 anonymous Users)
0 Members:


Collapse

> Similar Topics

  Topic Replies Topic Starter Views Last Action
No New Posts Headlights
2 WhiteMike 14,962 9th September 2016 - 10:09 PM
Last post by: AKENT
No New Posts HEADLIGHT ASSEMBLY DIFFERENCE BETWEEN 2003 VS 2004
9 jroth100 3,285 2nd September 2016 - 09:43 AM
Last post by: 2000J25SP
No New Posts headlight aim adjustments
0 SailorDave 837 6th July 2016 - 08:45 AM
Last post by: SailorDave
No New Posts Headlight assembly
3 poorboy428 920 26th May 2016 - 10:01 AM
Last post by: slowgls
No New Posts Header HELP!
2 esnow 9,443 9th May 2016 - 07:13 PM
Last post by: 2000J25SP


 



Copyright 2022 The Elantra Club    
Time is now: 29th March 2024 - 08:10 PM
Elantra Club is not affiliated in any way with Hyundai Motor America